Skip to content
BY 4.0 license Open Access Published by De Gruyter September 18, 2020

Enhancement of rotational vacuum friction by surface photon tunneling

  • Zhujing Xu ORCID logo , Zubin Jacob and Tongcang Li ORCID logo EMAIL logo
From the journal Nanophotonics

Abstract

When a neutral sphere is rotating near a surface in vacuum, it will experience a frictional torque due to quantum and thermal electromagnetic fluctuations. Such vacuum friction has attracted many interests but has been too weak to be observed. Here we investigate the vacuum frictional torque on a barium strontium titanate (BST) nanosphere near a BST surface. BST is a perovskite ferroelectric ceramic that can have large dielectric responses at GHz frequencies. At resonant rotating frequencies, the mechanical energy of motion can be converted to electromagnetic energy through resonant photon tunneling, leading to a large enhancement of the vacuum friction. The calculated vacuum frictional torques at resonances at sub-GHz and GHz frequencies are several orders larger than the minimum torque measured by an optically levitated nanorotor recently, and are thus promising to be observed experimentally. Moreover, we calculate the vacuum friction on a rotating sphere near a layered surface for the first time. By optimizing the thickness of the thin-film coating, the frictional torque can be further enhanced by several times.

1 Introduction

Quantum fluctuations of electromagnetic fields cause an attractive force between two neutral metallic plates, which was first calculated in 1948 and well known as Casimir force [1]. Besides the Casimir force between static macroscopic objects, the fluctuating electromagnetic fields can cause noncontact vacuum friction between two surfaces in relative motion [2], [3]. Many efforts have been made for studying the vacuum friction between various materials and configurations [4], [5], [6], [7], [8], [9], [10]. However, former attempts using atomic force microscopes had not successfully detected the vacuum friction [11], [12], [13]. The difficulty mainly comes from the small value of vacuum friction. It is thus worthwhile to understand the mechanisms of vacuum friction better and look for enhancements of the vacuum friction. At the same time, it is essential to develop a suitable ultrasensitive detector for the measurement.

In this letter, we investigate the vacuum friction on a rotating nanosphere levitated near a flat plate (Figure 1(a)), inspired by recent breakthroughs in levitated optomechanics. There are growing interests in using optically levitated dielectric particles in vacuum for precision measurements since they are well isolated from the environment and have ultrahigh sensitivity [14], [15], [16], [17], [18], [19], [20], [21]. Microspheres and nanospheres have been optically levitated near surfaces [22], [23]. Meanwhile, levitated nanoparticles have been driven to rotate up to 5 GHz by a circularly polarized laser [19]. Remarkably, a rotating nanoparticle levitated at 10−5 torr has measured a torque as small as 5 × 10−28 Nm in just 100 s [19].

Figure 1: Vacuum friction between a rotating nanosphere and a substrate.(a) A sphere with a radius of 75 nm rotates around the x axis. The z axis is normal to the substrate. (b) The imaginary part of the Green function (Eq. (3)) between a barium strontium titanate (BST) substrate and a nearby nanosphere. (c) The imaginary part of the Green function between a SiO2 substrate and a nearby nanosphere. (d) Calculated vacuum friction torque acting on a BST/silica nanosphere near a BST/silica surface as a function of the separation between the sphere and the substrate. The sphere rotates at a frequency of 150 MHz, which is a resonant frequency of BST. (e) The frictional torque on a BST/silica sphere near a BST/silica surface is shown as a function of the rotating frequency of the nanosphere. The separation between the sphere and the substrate is 300 nm. (f) The friction torque of a SiO2 sphere near a SiO2 surface is shown at a higher frequency range. The separation is 300 nm.
Figure 1:

Vacuum friction between a rotating nanosphere and a substrate.

(a) A sphere with a radius of 75 nm rotates around the x axis. The z axis is normal to the substrate. (b) The imaginary part of the Green function (Eq. (3)) between a barium strontium titanate (BST) substrate and a nearby nanosphere. (c) The imaginary part of the Green function between a SiO2 substrate and a nearby nanosphere. (d) Calculated vacuum friction torque acting on a BST/silica nanosphere near a BST/silica surface as a function of the separation between the sphere and the substrate. The sphere rotates at a frequency of 150 MHz, which is a resonant frequency of BST. (e) The frictional torque on a BST/silica sphere near a BST/silica surface is shown as a function of the rotating frequency of the nanosphere. The separation between the sphere and the substrate is 300 nm. (f) The friction torque of a SiO2 sphere near a SiO2 surface is shown at a higher frequency range. The separation is 300 nm.

Similar to the vacuum frictional force between two plates that have relative motions [2], [3], there will be a vacuum frictional torque on a nanosphere rotating at a high speed [6], [10]. Thus a levitated nanorotor provides a promising method to detect the vacuum frictional torque. Former calculations have found that the vacuum frictional torque on a 150 nm-diameter silica nanosphere near a silica surface is about 6 × 10−29 Nm at a separation of 300 nm when the sphere is rotating at 1 GHz and both the surface and the sphere are at a temperature of 300 K [19]. To measure the vacuum friction between a silica sphere and a silica plate, the experiment needs to be conducted under ultrahigh vacuum below 10−9 torr [19]. In this work, we propose to use BST, which is a perovskite ferroelectric ceramic that can have a large dielectric resonance at GHz frequency [24], to dramatically enhance the vacuum friction by resonant surface photon tunneling at sub-GHz and GHz frequencies. We show that the vacuum frictional torque on a BST sphere near a BST plate can be significantly enhanced to 3.6 × 10−24 Nm and 8.1 × 10−23 Nm through resonant photon tunneling at a rotating frequency of 150 MHz and 3.5 GHz, respectively. So the torque on a BST sphere near a BST plate can be measured at a pressure of about 10−4 torr.

The enhancement of the vacuum friction comes from photon tunneling between two surfaces. At the resonant condition, the conversion of the mechanical energy of motion to the electromagnetic energy is realized efficiently. In the domain of the rotation frequency, there are two resonances that correspond to the normal and anomalous Doppler effect [25], [26], [27]. The resonant tunneling occurs when the mechanical rotation frequency matches the sum or the difference of the surface plasmon or phonon polariton frequencies. For metals and semiconductors, the surface plasmon or phonon polariton frequency is usually on the order of 1014 Hz and 1012 Hz, respectively. Such a high surface polariton frequency makes it extremely difficult to experimentally reach the resonant condition [25], [26], [27]. Here we choose a ferroelectric material BST which has low surface polariton frequency at GHz range [24]. The dielectric properties of BST can also be tuned by fabrication and doping. When the mechanical rotating frequency of the sphere is also around GHz, the vacuum frictional torque can be significantly enhanced due to the resonant photon tunneling. In this way, the vacuum frictional torque is several orders higher than the minimum detectable torque. Besides the huge enhancement, for the first time we will show the vacuum friction between a BST sphere and a multilayer coating on top of a BST substrate. The torque can be further increased by several times by optimizing the thickness of the coating layer.

This paper is organized as follows. We show the general method of calculating the vacuum frictional torque on a rotating nanosphere and discuss the condition for the resonant photon tunneling in Section 2. The calculated friction torque acting on a BST sphere near a BST plate is presented in Section 3. In this section, we show a significant enhancement of the friction torque. Section 4 is devoted to showing the torque on a BST sphere near a multilayer coating on top of a BST substrate. The transfer matrix for calculating the optical matrix of the multilayer structure is introduced. Further enhancement of the friction torque is demonstrated.

2 Resonances in a rotating nanosphere near a surface

As a ferroelectric material, BST possesses many exceptional dielectric properties such as high dielectric constant, low loss and large electric-field dielectric tunability over a wide frequency range [24]. Especially, it has low surface polariton frequency which is favorable for enhancing the vacuum friction torque at sub-GHz and GHz frequencies.

We investigate on a case that a sphere with radius r is rotating with frequency Ω in vacuum and is placed at a separation of d from the substrate as shown in Figure 1(a). We work within the nonrelativistic and near-field limit. Thus the separation needs to be far smaller than both c/Ω (≈5 cm at 1 GHz) and c/kBTj (≈8 μm at 300 K). Besides, the dipole approximation requires the radius of the nanosphere to be sufficiently smaller than the separation. The friction torque experienced by the sphere is written as [10].

(1)Mp=2π[n1(ωΩ)n0(ω)]×Im[α(ωΩ)]Im[G¯(ω)]dω

where nj(T)=[exp(ω/kBTj)1]1 is the Bose–Einstein distribution function at temperature Tj and j = 0, 1 are for the substrate and the sphere, respectively. α(ω) is the electric polarizability of the nanosphere. G¯(ω) is the Green function such that G¯(ω)=[Gyy(ω)+Gzz(ω)]/2, where Gyy and Gzz are electromagnetic Green tensor components and x is the axis of the rotation. The polarizability and the Green function can be described as

(2)α(ω)=4πϵ0R3ϵsp(ω)1ϵsp(ω)+2,
(3)G¯(ω)=38πϵ0(2d)3ϵsub(ω)1ϵsub(ω)+1,

where ϵsp and ϵsub are the dielectric functions of the sphere and the substrate, respectively. The equations above are for the situation that the rotation axis of the sphere is parallel to the substrate surface. When the rotating axis is normal to the surface, the Green function has a factor of 23 difference and hence the friction torque is [28].

(4)Mn=23Mp,

where Mn and Mp stand for the torque when the sphere is rotating normal and parallel to the surface, respectively. Notice that all the following calculations of the vacuum frictional torque are for the parallel case. As we can see, the friction torque depends on the optical properties of the interacting materials. The dielectric functions of different dielectric materials can be modeled as Lorentz oscillators, which treat each discrete vibrational mode as a classical damped harmonic oscillator:

(5)ϵ(ω)=ϵ(1+ωL2ωT2ωT2ω2iΓω),

where ϵ is the permittivity in the high-frequency limit, ωL is the longitudinal polar-optic phonon frequency, ωT is the transverse polar-optic phonon frequency and γ is the damping coefficient.

As mentioned above, we are looking at the resonant photon tunneling between surface phonon polaritons to realize enhancement of the vacuum friction. Similar to the normal and anomalous Doppler effect for the system of two sliding plates [25], [26], [27], rotational friction between a rotating sphere and a flat plate also has such resonances. BST is a good candidate for realizing such resonant photon tunneling since it can support low-frequency surface polariton modes. The optical phonon parameters of BST are ϵ=2.896, ωL=1.3×1010s1, ωT=5.7×109s1, Γ=2.8×108s1 [24].

The friction increases significantly at the rotating frequency Ω=|ω1p±ω2p| which correspond to the resonant generation of surface polaritons. Here Ω is the rotating frequency of the sphere. ω1p and ω2p are surface polariton frequencies such that Re(ϵ(ω1p))=2 and Re(ϵ(ω2p))=1, which lead to large α(ω) and G¯(ω). Two resonant frequencies are ω1p=1.06×1010s1 and ω2p=1.15×1010s1. Therefore, when the rotation frequency Ω=|ω1ω2|=2π×150MHz or Ω=ω1+ω2=2π×3.52GHz, the friction will be greatly enhanced. Figure 1(b) shows the Green function that connects the dipole moment fluctuation of the sphere and the induced electromagnetic field on a BST surface. As a comparison, the Green function for a silica surface is presented in Figure 1(c). The frequency of surface polaritons for a silica surface [29] is around 1013 Hz, which is several orders higher than the frequency of BST. To meet the condition of resonant photon tunneling between a silica sphere and a silica plate, the rotation frequency of the sphere will need to reach 1013 Hz which cannot be achieved experimentally.

3 Vacuum friction between a BST nanosphere and a BST plate

The calculated vacuum friction between a BST sphere and a BST plate is presented in this section. Here, we investigate on a case that the radius of the sphere is 75 nm [19] and the sphere and the plate have the same temperature of 300 K. At a separation of 300 nm, the calculated friction torque is shown as a function of rotating frequency in Figure 1(e). The blue solid curve corresponds to the friction between a BST sphere and a BST plate. It shows two resonant peaks of the torque at 150 MHz and 3.52 GHz as expected before. The amplitude of the friction torque at two resonant frequencies are several orders higher than the nonresonant part. The maximum torque of 8.06 × 10−23 Nm is achieved at 3.52 GHz. The red dashed curve is the friction torque acting on a silica sphere near a silica plate, for comparison. The low-frequency surface polariton mode and resonant photon tunneling significantly enhance the amplitude of the vacuum friction. At 150 MHz and 3.52 GHz, the friction torque between a BST sphere and a BST surface has an enhancement of about 4 × 105 compared to the torque between a silica sphere and a silica surface.

Figure 1(f) shows the calculated torque for silica at much higher rotation frequencies. Similarly, silica also has resonant photon tunneling conditions and at such frequencies, the torque can also be greatly enhanced. At a rotating frequency of around 100 THz, the torque can also be near 10−22 Nm. However, this frequency is far beyond the current experimental limit. The calculated friction torque as a function of the separation between the sphere and the substrate is shown in Figure 1(d) at a rotating frequency of 150 MHz, which is the resonant frequency of BST. For each separation, the enhancement is more than five orders.

A recent experiment has detected a torque of 5 × 10−28 Nm with an optically levitated nanosphere at 10−5 torr [19]. It is four orders smaller than the vacuum frictional torque on a BST sphere at resonant frequency. Another factor that can affect the detection of vacuum friction is the air damping torque. The air damping torque on a rotating nanosphere due to residual air molecules in the vacuum chamber can be described as [30]:

(6)Mair=πpΩ(2r)411.9762mgasπkBT,

where p is the air pressure, r is the sphere radius, mgas=4.8×1026kg is the mass of the air molecule and T is the temperature of the surrounding air molecules. At the pressure of 10−4 torr, the air damping torque acting on the sphere is 4.5 × 10−24 Nm at a rotating frequency of 150 MHz at room temperature, which is about one orders smaller than the targeted vacuum friction torque. 10−4 torr and lower pressures have been achieved in levitation experiments [19], [31]. Compared to silica, the requirement of pressure for measuring vacuum friction on a BST nanosphere is substantially relaxed.

4 Effects of surface coating

We have demonstrated the vacuum friction between a BST sphere and a BST plate and showed that the friction can be enhanced by several orders due to the surface resonant photon tunneling. It will be easier to experimentally realize this condition when the resonant frequency is as low as possible. In this section we show that the resonant frequency can be lowered by thin-film coating.

We investigate on the friction torque on a BST sphere near a surface that has a thin layer of dielectric coating on top of a BST substrate as shown in Figure 2(a). To calculate the vacuum frictional torque, we need to get the reflection coefficients for the layered structure by the transfer matrix method. For a surface that has a thin layer on top of a substrate, the transfer matrix for the p(s) polarization is given as [32], [33]

(7)Tp(s)=D01p(s)P(L1)D12p(s),

where L1 is the thickness of the thin layer. Here j = 0, 1, 2 stands for the vacuum between the sphere and the surface, the thin layer, and the BST substrate, respectively. Dj,j+1p(s) is the transmission matrix between layer j and j+1 for the p(s) polarization and it can be written as

(8)Djj+1p(s)=12[1+ηj,j+1p(s)1ηj,j+1p(s)1ηj,j+1p(s)1+ηj,j+1p(s)],

where ηj,j+1p(s) is given as

(9)ηj,j+1p=ϵjkj+1,zϵj+1kj,z,ηj,j+1s=kj+1,zkj,z.

Here kj,z=ϵω2/c2k2 is the vertical wave vector for the jth layer. k is the wave vector parallel to the surface. P(Lj) is the propagation matrix in the jth layer for both p and s polarizations and it is given as

(10)P(Lj)=[eikj,zLj00eikj,zLj].
Figure 2: Vacuum friction between a barium strontium titanate (BST) sphere and a BST substrate with a single-layer coating.(a) A sphere with a radius of 75 nm rotates around the x axis. The z axis is the direction normal to the substrate. The plate consists of a thin layer of dielectric material (shown in yellow) and a BST substrate (shown in blue). (b) Calculated vacuum frictional torque acting on the nanosphere as a function of the separation between the sphere and the substrate. The sphere rotates at a frequency of 10 MHz. The red, yellow, and green dashed curve correspond to the case for a 20-nm SiC, 20-nm Si3N4, and a 60-nm SiO2 thin layer. The blue solid curve is for the case when there is no coating. (c) The frictional torque is shown as a function of the rotating frequency of the nanosphere. The separation is 300 nm. The blue solid curve shows the case when there is no coating on the BST substrate. The red, yellow, and green dashed curve correspond to the case for a 20-nm SiC, a 20-nm Si3N4, and a 60-nm SiO2 thin layer on top of the BST substrate. (d) The frictional torque is shown as a function of the thickness of the thin layer on top of the BST substrate for the case of SiC, Si3N4, and SiO2. Here the separation is 300 nm and the rotating frequency is 10 MHz.
Figure 2:

Vacuum friction between a barium strontium titanate (BST) sphere and a BST substrate with a single-layer coating.

(a) A sphere with a radius of 75 nm rotates around the x axis. The z axis is the direction normal to the substrate. The plate consists of a thin layer of dielectric material (shown in yellow) and a BST substrate (shown in blue). (b) Calculated vacuum frictional torque acting on the nanosphere as a function of the separation between the sphere and the substrate. The sphere rotates at a frequency of 10 MHz. The red, yellow, and green dashed curve correspond to the case for a 20-nm SiC, 20-nm Si3N4, and a 60-nm SiO2 thin layer. The blue solid curve is for the case when there is no coating. (c) The frictional torque is shown as a function of the rotating frequency of the nanosphere. The separation is 300 nm. The blue solid curve shows the case when there is no coating on the BST substrate. The red, yellow, and green dashed curve correspond to the case for a 20-nm SiC, a 20-nm Si3N4, and a 60-nm SiO2 thin layer on top of the BST substrate. (d) The frictional torque is shown as a function of the thickness of the thin layer on top of the BST substrate for the case of SiC, Si3N4, and SiO2. Here the separation is 300 nm and the rotating frequency is 10 MHz.

With the transfer matrix M, the optical properties such as reflection, transmission and absorption for the layered structure can be calculated. The reflection coefficients for the p(s) polarization of the layered structure is [32], [33].

(11)rp(s)=T21p(s)/T11p(s).

where T21p(s) and T21p(s) are the components of the transfer matrix T. To calculate the vacuum friction between a sphere and a layered structure, we need to get the electromagnetic Green tensor and it is given as [34]

(12)G(ω)=i0dkke2ikzd[rp(ω,k)(kz/2000kz/2000k2/kz)+rs(ω,k)(k2/2kz000k2/2kz0000)],

where d is the separation between the sphere and plate, k=ω/c is the total wave vector, k is the wave vector parallel to the surface, kz=k2k2 is the wave vector perpendicular to the surface. rs and rp are the reflection coefficients of the layered structure which have been calculated by the transfer matrix. Therefore, the Green function that associates the dipole moment fluctuations of the sphere and the induced electromagnetic field on the layered surface is given as

(13)G¯(ω)=12(Gyy+Gzz)=i20dkke2ikzd[rp(ω,k)kz2+rs(ω,k)k22kz+rp(ω,k)k2kz].

Based on the transfer matrix introduced above, now we can calculate the friction torque experienced by a sphere near a layered structure as shown in Figure 2(a). At a rotating frequency of 10 MHz, the calculated friction as a function of the separation is shown in Figure 2(b). The red, yellow, and green dashed curve is the case for a single layer of 20-nm SiC, 20-nm Si3N4, and 60-nm SiO2 on top of the BST. The blue solid curve is the case for a BST sphere and a BST substrate, for comparison. The optical properties of SiC, Si3N4, and SiO2 can be found in [29], [34]. We can see that the torque for the single-layer coating is enhanced by about four times compared to the no-coating case. We also show the calculated friction as a function of the rotating frequency in Figure 2(c) when the separation is 300 nm. Notice that one of the resonant frequencies (originally at 150 MHz) shifts to the left. This explained the enhancement of the friction torque for the single-layer structure at low-frequency range. This layered structure is favorable for the experiment since it gives a larger torque at lower rotating frequency. At this frequency, the mechanical rotor behaves more stable and hence easier for the measurement to be performed. We also show the dependence of thickness of the thin layer on the friction torque in Figure 2(d). It shows that 20-nm SiC, 20-nm Si3N4, and 60-nm SiO2 give the largest friction torque. It is essential to find the optimum thickness of the coating to get the largest torque.

Beyond that, we also calculated the friction torque for the double-layer coating. The configuration is shown in Figure 3(a). The top is a thin layer of BST as shown in blue. The middle one is a 20-nm SiC thin layer similar to the former case and the bottom is a BST substrate. Similar to the single-layer coating, the transfer matrix for the p(s) polarization is given as Tp(s)=D01p(s)P(L1)D12p(s)P(L2)D23p(s), where L1 and L2 is the thickness of the first and second layer coating, respectively. Djj+1p(s) is the transmission matrix and P(Lj) is the propagation matrix. At a separation of 300 nm, the calculated friction torque as a function of the rotating frequency is presented in Figure 3(b). The blue solid, red dashed, and green dashed curves corresponds to a thin layer of 0-, 15-, and 50-nm BST on top of a 20-nm SiC-coated BST plate. The torque for the double-layer is only slightly larger than the one with the single-layer coating at low-frequency range. Figure 3(c) shows the friction torque as a function of the thickness of the top BST layer when the rotating frequency is 10 MHz and the separation is 300 nm.

Figure 3: Vacuum friction between a barium strontium titanate (BST) sphere and a BST substrate with a double-layer coating on top.(a) A sphere with a radius of 75 nm rotates around the x axis, which is parallel to the plate. The plate consists of a thin layer of BST (shown in blue), a thin layer of SiC (shown in yellow) and a BST substrate. (b). Calculated vacuum frictional torque as a function of the rotating frequency of the nanosphere. The separation is 300 nm. The blue solid, red dashed, and green dashed curves correspond to a thin layer of 0-, 15-, and 50-nm BST on top of a 20-nm SiC-coated BST plate. (c). When the thickness of the second layer (SiC) is fixed to 20 nm and the rotating frequency is 10 MHz, the friction torque is shown as a function of the thickness of the first layer (BST). The separation is 300 nm.
Figure 3:

Vacuum friction between a barium strontium titanate (BST) sphere and a BST substrate with a double-layer coating on top.

(a) A sphere with a radius of 75 nm rotates around the x axis, which is parallel to the plate. The plate consists of a thin layer of BST (shown in blue), a thin layer of SiC (shown in yellow) and a BST substrate. (b). Calculated vacuum frictional torque as a function of the rotating frequency of the nanosphere. The separation is 300 nm. The blue solid, red dashed, and green dashed curves correspond to a thin layer of 0-, 15-, and 50-nm BST on top of a 20-nm SiC-coated BST plate. (c). When the thickness of the second layer (SiC) is fixed to 20 nm and the rotating frequency is 10 MHz, the friction torque is shown as a function of the thickness of the first layer (BST). The separation is 300 nm.

5 Conclusion

In this paper, we have calculated the vacuum friction between a rotating sphere and a close surface. We notice that BST has low surface phonon polariton frequency which can be mechanically excited. At two resonant rotating frequencies, the mechanical energy of the rotating sphere can be converted to the electromagnetic field energy and hence significantly enhance the vacuum friction torque. This provides us a more practical scheme to measure the long-sought vacuum friction torque. Moreover, we find that applying a single-layer coating on top of the BST substrate can further increase the friction torque by four times. The torque not only depends on the rotating frequency and the separation, but also relates to the thickness of the layer. The friction torque for the double-layer coating on the BST substrate is also presented in the content. In the future, it will be interesting to study whether more complex metamaterials [35] and topological materials [36] can further enhance the vacuum friction.


Corresponding author: Tongcang Li, Department of Physics and Astronomy, Purdue University, West Lafayette, IN 47907, USA; School of Electrical and Computer Engineering, Purdue University, West Lafayette, IN 47907, USA; Purdue Quantum Science and Engineering Institute, Purdue University, West Lafayette, IN 47907, USA; and Birck Nanotechnology Center, Purdue University, West Lafayette, IN 47907, USA, E-mail:

Award Identifier / Grant number: QUEST

Funding source: Office of Naval Research

Award Identifier / Grant number: N00014-18-1-2371

Acknowledgments

The authors are grateful to receive support from the DARPA QUEST program and the Office of Naval Research under Grant No. N00014-18-1-2371.

  1. Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: This research was supported by the DARPA QUEST program and the Office of Naval Research under Grant No. N00014-18-1-2371.

  3. Conflict of interest statement: The authors declare no conflicts of interest regarding this article.

References

[1] H. B. G. Casimir, “On the attraction between two perfectly conducting plates,” Proceedings, vol. 51, pp. 793–795, 1948.Search in Google Scholar

[2] J. B. Pendry, “Shearing the vacuum - quantum friction,” J. Phys. Condens. Matter, vol. 9, pp. 10301–10320, 1997, https://doi.org/10.1088/0953-8984/9/47/001.Search in Google Scholar

[3] A. I. Volokitin and B. N. J. Persson, “Theory of friction: the contribution from a fluctuating electromagnetic field,” J. Phys. Condens. Matter, vol. 11, pp. 345–359, 1999, https://doi.org/10.1088/0953-8984/11/2/003.Search in Google Scholar

[4] P. A. Maia Neto and S. Reynaud, “Dissipative force on a sphere moving in vacuum,” Phys. Rev. A, vol. 47, pp. 1639–1646, 1993, https://doi.org/10.1103/physreva.47.1639.Search in Google Scholar

[5] F. Intravaia, R. O. Behunin and D. A. R. Dalvit, “Quantum friction and fluctuation theorems,” Phys. Rev. A, vol. 89, p. 050101, 2014, https://doi.org/10.1103/physreva.89.050101.Search in Google Scholar

[6] A. Manjavacas and F. J. García de Abajo, “Vacuum friction in rotating particles,” Phys. Rev. Lett., vol. 105, p. 113601, 2010, https://doi.org/10.1103/physrevlett.105.113601.Search in Google Scholar

[7] M. S. Tomassone and A. Widom, “Electronic friction forces on molecules moving near metals,” Phys. Rev. B, vol. 56, pp. 4938–4943, 1997, https://doi.org/10.1103/physrevb.56.4938.Search in Google Scholar

[8] A. I. Volokitin and B. N. J. Persson, “Resonant photon tunneling enhancement of the van der waals friction,” Phys. Rev. Lett., vol. 91, p. 106101, 2003, https://doi.org/10.1103/physrevlett.91.106101.Search in Google Scholar

[9] A. I. Volokitin and B. N. J. Persson, “Quantum friction,” Phys. Rev. Lett., vol. 106, p. 094502, 2011, https://doi.org/10.1103/physrevlett.106.094502.Search in Google Scholar

[10] R. Zhao, A. Manjavacas, F. J. García de Abajo, and J. B. Pendry, “Rotational quantum friction,” Phys. Rev. Lett., vol. 109, p. 123604, 2012, https://doi.org/10.1103/physrevlett.109.123604.Search in Google Scholar

[11] I. Dorofeyev, H. Fuchs, G. Wenning, and B. Gotsmann, “Brownian motion of microscopic solids under the action of fluctuating electromagnetic fields,” Phys. Rev. Lett., vol. 83, pp. 2402–2405, 1999, https://doi.org/10.1103/physrevlett.83.2402.Search in Google Scholar

[12] B. Gotsmann and H. Fuchs, “Dynamic force spectroscopy of conservative and dissipative forces in an al-au(111) tip-sample system,” Phys. Rev. Lett., vol. 86, pp. 2597–2600, 2001, https://doi.org/10.1103/physrevlett.86.2597.Search in Google Scholar

[13] B. C. Stipe, H. J. Mamin, T. D. Stowe, T. W. Kenny, and D. Rugar, “Noncontact friction and force fluctuations between closely spaced bodies,” Phys. Rev. Lett., vol. 87, p. 096801, 2001, https://doi.org/10.1103/physrevlett.87.096801.Search in Google Scholar

[14] G. Ranjit, M. Cunningham, K. Casey, and A. A. Geraci, “Zeptonewton force sensing with nanospheres in an optical lattice,” Phys. Rev. A, vol. 93, p. 053801, 2016, https://doi.org/10.1103/physreva.93.053801.Search in Google Scholar

[15] Z. Xu and T. Li, “Detecting casimir torque with an optically levitated nanorod,” Phys. Rev. A, vol. 96, p. 033843, 2017, https://doi.org/10.1103/physreva.96.033843.Search in Google Scholar

[16] J. Ahn, Z. Xu, J. Bang, et al., “Optically levitated nanodumbbell torsion balance and ghz nanomechanical rotor,” Phys. Rev. Lett., vol. 121, p. 033603, 2018, https://doi.org/10.1103/physrevlett.121.033603.Search in Google Scholar

[17] R. Reimann, M. Doderer, E. Hebestreit, et al., “Ghz rotation of an optically trapped nanoparticle in vacuum,” Phys. Rev. Lett., vol. 121, p. 033602, 2018, https://doi.org/10.1103/physrevlett.121.033602.Search in Google Scholar

[18] C. P. Blakemore, A. D. Rider, S. Roy, Q. Wang, A. Kawasaki, and G. Gratta, “Three-dimensional force-field microscopy with optically levitated microspheres,” Phys. Rev. A, vol. 99, p. 023816, 2019, https://doi.org/10.1103/physreva.99.023816.Search in Google Scholar

[19] J. Ahn, Z. Xu, J. Bang, P. Ju, X. Gao, and T. Li, “Ultrasensitive torque detection with an optically levitated nanorotor,” Nat. Nanotechnol., vol. 15, pp. 89–93, 2020, https://doi.org/10.1038/s41565-019-0605-9.Search in Google Scholar

[20] Y. Zheng, L.-M. Zhou, Y. Dong, et al., “Robust optical-levitation-based metrology of nanoparticle’s position and mass,” Phys. Rev. Lett., vol. 124, p. 223603, 2020, https://doi.org/10.1103/physrevlett.124.223603.Search in Google Scholar

[21] J. Bang, T. Seberson, P. Ju, et al., “5D Cooling and precession-coupled nonlinear dynamics of a levitated nanodumbbell,” arXiv:2004.02384, 2020.Search in Google Scholar

[22] R. Diehl, E. Hebestreit, R. Reimann, F. Tebbenjohanns, M. Frimmer, and L. Novotny, “Optical levitation and feedback cooling of a nanoparticle at subwavelength distances from a membrane,” Phys. Rev. A, vol. 98, p. 013851, 2018, https://doi.org/10.1103/physreva.98.013851.Search in Google Scholar

[23] L. Magrini, R. A. Norte, R. Riedinger, et al., “Near-field coupling of a levitated nanoparticle to a photonic crystal cavity,” Optica, vol.5, pp. 1597–1602, 2018, https://doi.org/10.1364/optica.5.001597.Search in Google Scholar

[24] A. O. Turky, M. Mohamed Rashad, A. E.-H. Taha Kandil, and M. Bechelany, “Tuning the optical, electrical and magnetic properties of ba0.5sr0.5tixm1–xo3 (bst) nanopowders,” Phys. Chem. Chem. Phys., vol. 17, pp. 12553–12560, 2015, https://doi.org/10.1039/c5cp00319a.Search in Google Scholar

[25] Y. Guo and Z. Jacob, “Giant non-equilibrium vacuum friction: role of singular evanescent wave resonances in moving media,” J. Opt., vol. 16, p. 114023, 2014, https://doi.org/10.1088/2040-8978/16/11/114023.Search in Google Scholar

[26] Y. Guo and Z. Jacob, “Singular evanescent wave resonances in moving media,” Opt. Express, vol. 22, pp. 26193–26202, 2014, https://doi.org/10.1364/oe.22.026193.Search in Google Scholar

[27] A. Volokitin, “Resonant photon emission during relative sliding of two dielectric plates,” Mod. Phys. Lett., vol. 35, p. 2040011, 2020, https://doi.org/10.1142/s0217732320400118.Search in Google Scholar

[28] A. I. Volokitin, “Singular resonance in fluctuation-induced electromagnetic phenomena at the rotation of a nanoparticle near the surface of a condensed medium,” JETP Lett., vol. 108, pp. 147–154, 2018, https://doi.org/10.1134/s0021364018140138.Search in Google Scholar

[29] J. Kischkat, S. Peters, B. Gruska, et al., “Mid-infrared optical properties of thin films of aluminum oxide, titanium dioxide, silicon dioxide, aluminum nitride, and silicon nitride,” Appl. Opt., vol. 51, pp. 6789–6798, 2012, https://doi.org/10.1364/ao.51.006789.Search in Google Scholar

[30] J. Corson, G. W. Mulholland, and M. R. Zachariah, “Calculating the rotational friction coefficient of fractal aerosol particles in the transition regime using extended kirkwood-riseman theory,” Phys. Rev. E, vol. 96, p. 013110, 2017, https://doi.org/10.1103/physreve.96.013110.Search in Google Scholar

[31] F. Tebbenjohanns, M. Frimmer, A. Militaru, V. Jain, and L. Novotny, “Cold damping of an optically levitated nanoparticle to microkelvin temperatures,” Phys. Rev. Lett., vol. 122, p. 223601, 2019, https://doi.org/10.1103/physrevlett.122.223601.Search in Google Scholar

[32] L. Ge, X. Shi, Z. Xu, and K. Gong, “Tunable casimir equilibria with phase change materials: from quantum trapping to its release,” Phys. Rev. B, vol. 101, p. 104107, 2020, https://doi.org/10.1103/physrevb.101.104107.Search in Google Scholar

[33] T. Zhan, X. Shi, Y. Dai, X. Liu, and J. Zi, “Transfer matrix method for optics in graphene layers,” J. Phys. Condens. Matter, vol. 25, p. 215301, 2013, https://doi.org/10.1088/0953-8984/25/21/215301.Search in Google Scholar

[34] A. Manjavacas, F. J. Rodríguez-Fortuño, F. J. García de Abajo, and A. V. Zayats, “Lateral casimir force on a rotating particle near a planar surface,” Phys. Rev. Lett., vol. 118, p. 133605, 2017, https://doi.org/10.1103/physrevlett.118.133605.Search in Google Scholar

[35] X. Ni, Z. J. Wong, M. Mrejen, Y. Wang, and X. Zhang, “An ultrathin invisibility skin cloak for visible light,” Science, vol. 349, p. 1310, 2015, https://doi.org/10.1126/science.aac9411.Search in Google Scholar

[36] Q.-D. Jiang and F. Wilczek, “Quantum atmospherics for materials diagnosis,” Phys. Rev. B, vol. 99, p. 201104, 2020. https://doi.org/10.1103/PhysRevB.99.201104.Search in Google Scholar

Received: 2020-07-12
Accepted: 2020-08-30
Published Online: 2020-09-18

© 2020 Zhujing Xu et al., published by De Gruyter, Berlin/Boston

This work is licensed under the Creative Commons Attribution 4.0 International License.

Downloaded on 28.3.2024 from https://www.degruyter.com/document/doi/10.1515/nanoph-2020-0391/html
Scroll to top button